Vigo VG6061CHCL36W Instalační příručka stáhnout pdf

This Installation Guide uses the following symbols to indicate important information.

Always observe the instructions indicated by these symbols.

VIGO INDUSTRIES INSTALLATION GUIDE FOR

SHOWER ENCLOSURE (MODEL VG06061)

Instructions that, if ignored, could result in death or serious personal injury caused by

incorrect handling or installation of the product. These instructions must be observed for

safe installation.

Maintenance and other important non-personal injury and non-material damage instructions

or statements that should be observed.

It is highly advised to dry fit the unit prior to any installation.

IMPORTANT

SAFETY PRECAUTIONS!

WARNING!

The instructions for the following unit is based off of the Vigo brand shower base. The

instructions can not be provided for any other installation other than that of the Vigo brand.

The warranty will be voided if the following was not performed properly.

CAUTION!

1 2 3 4 5 6 ... 17 18

IMPORTANT 1
MODEL VG06061 10

Shrnutí obsahu

Strany 1 - IMPORTANT

This Installation Guide uses the following symbols to indicate important information.Always observe the instructions indicated by these symbols.VIGO I

Strany 2

10MODEL VG06061FIG.7SEAL STRIP INSTALLATION DIAGRAM1310THIS SIDE MUSTLOOK INSIDE THECABINMAGNET3/8"[10mm]51015131413D. INSTALLING THE WATER

Strany 3

11MODEL VG06061HEX SCREWSIDE GLASSPANEL (4)DOOR (13)THINGASKETVIEW FROM THE TOPHINGE (8)OUTSIDE OFTHE CABININSIDE OFTHE CABINPLATE E. INSTALLING

Strany 4

F. INSTALLING SIDE GLASS PANEL (PART #5)1. Install the side seal strip (#6) to the wall side of the side glass panel (#5). Install the magneticsid

Strany 5

13MODEL VG0606121316G. INSTALLING THE SIDE & FRONT PANEL SUPPORT1. Install the support assembly (#3) onto the side glass panel (#4) approximately

Strany 6

I. APPLYING THE SILICONE1. Apply clear silicone caulking to the inside between the wall and side seal strip.2. Apply clear silicone caulk to the in

Strany 7

IMPORTANT! WAIT 24 HOURS BEFORE USING SHOWER DO NOT ALLOW WATER TO DIRECTLY HIT DOOR SEAL STRIPSMODEL VG0606115J. HANDLE INSTALLATION1. Asse

Strany 8

MODEL VG0606116

Strany 9

CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANELA. Use mild liquid household cleaners to keep metal surface bright and clean. Rinse well and

Strany 10 - MODEL VG06061

MODEL VG06061SHOWER ENCLOSURE LIMITED LIFETIME WARRANTYEFFECTIVE JANUARY 1, 2010

Strany 11

21234679111012138MODEL VG06061NOTE: INSTALLATION MUST BE DONE BY A QUALIFIED, LICENSED PLUMBER.GLASS THICKNESS 3/8"PLEASE READ INSTRUCTIONS BEFOR

Strany 12

31.2.3. SUPPORT ASSEMBLY4.SIDE GLASS PANEL7.GLASS SUPPORT8.HINGE ASSEMBLY12.DOOR HANDLEASSEMBLYDOOR BOTTOMSEAL STRIP15.13. DOOR6.SIDE SEAL STRIP9. BOT

Strany 13

ABCCDMODEL VG060614A, B, C & D DIMENSIONS WERE MEASURED AFTER SHOWER ENCLOSURE WASCOMPLETELY INSTALLED19 1/2"X71 5/8"15 1/2"X71 5/8

Strany 14

5MODEL VG06061FRONT GLASSPANELDOOR PANEL SIDE GLASSPANELFIG. 1 (GLASS CONFIGURATION DIAGRAM)5134FRONT GLASSPANELDOOR PANELSIDE GLASSPANEL4135LEFT SIDE

Strany 15

INSTALLATION STEPSA. INSTALLING THE BOTTOM RAIL6MODEL VG06061PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION1. Remove the plastic layer from the base

Strany 16

STUDFIG.2FIG.3AB911THIS EDGE LOOKSOUTSIDE OF THE SHOWERTHIS EDGE LOOKSINSIDE OF THE SHOWER18FIG.2A7MODEL VG06061TOP REMOVES TOINSTALL 3/4&qu

Strany 17

B. HINGE INSTALLATION1. Clean the glass surface on the side glass panel (#4) where the hinges (#8) are to be installedwith rubbing alcohol.2. Po

Strany 18

9MODEL VG06061WALLSIDEC. INSTALLING SIDE GLASS PANEL (PART #4)1. Arrange glass to the preferred configuration. (see diagram on page 5) These i